MangoH Red session logged out

While I was working with voiceCallApp in the MangoH red, I was experimenting with cm radio on and cm radio off commands and while doing this MangoH Red was logged out and I could not login back again. When I try to re-install the firmware image I am getting the below error
FDT version: 1.0.1902.1
Awaiting adapter …
Setting images preference …
Enabling selective suspend …
Firmware download failed.
Primary error code: 51 - Failed to switch device to BOOT&HOLD mode.
Secondary error code: 201 - Failed to switch device to QDL mode.
Device error code: 0x0 - Unknown device error code.
Preexisting images information:
Current:
Firmware:
ImageId:
BuildId:
Configuration:
ImageId:
BuildId:
Final images information:
Current:
Firmware:
ImageId:
BuildId:
Configuration:
ImageId:
BuildId:
OEM PRI:
IMEI:
Total time elapsed: 248250 ms.
Images downloaded:

When I probed the serial logs in Moba Xterm on the Serial port, I am seeing the below logs

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00094
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=jenkins
S - Boot Config, 0x000002e1
B - 1216 - PBL, Start
B - 3720 - bootable_media_detect_entry, Start
B - 4368 - bootable_media_detect_success, Start
B - 4372 - elf_loader_entry, Start
B - 7826 - auth_hash_seg_entry, Start
B - 31480 - auth_hash_seg_exit, Start
B - 82876 - elf_segs_hash_verify_entry, Start
B - 129938 - PBL, End
B - 138348 - SBL1, Start
B - 196176 - pm_device_init, Start
B - 216367 - PM_SET_VAL:Skip
D - 18452 - pm_device_init, Delta
B - 217678 - boot_config_data_table_init, Start
D - 30 - boot_config_data_table_init, Delta - (0 Bytes)
B - 226432 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B - 233325 - sbl1_ddr_set_params, Start
B - 237137 - Pre_DDR_clock_init, Start
D - 213 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 249856 - pm_driver_init, Start
D - 4453 - pm_driver_init, Delta
B - 256108 - cpr_init, Start
D - 91 - cpr_init, Delta
B - 260805 - cpr_cx_mx_apc_vol_update, Start
D - 91 - cpr_cx_mx_apc_vol_update, Delta
B - 275964 - clock_init, Start
D - 152 - clock_init, Delta
B - 276208 - boot_flash_init, Start
D - 39223 - boot_flash_init, Delta
B - 318450 - boot_flash_swi_ddr_init, Start
D - 29402 - boot_flash_swi_ddr_init, Delta
B - 485102 - hw_family:5, hw_type:28, hw_rev:40
B - 489067 - SSMEM init OK
B - 506147 - USB non-zero endpoint requirements: 9 in, 5 out
B - 507794 - opening partition 0:SWIFOTA
B - 509990 - error for readpage:0

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00094
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=jenkins
S - Boot Config, 0x000002e1
B - 1216 - PBL, Start
B - 3720 - bootable_media_detect_entry, Start
B - 4374 - bootable_media_detect_success, Start
B - 4378 - elf_loader_entry, Start
B - 7832 - auth_hash_seg_entry, Start
B - 31485 - auth_hash_seg_exit, Start
B - 82885 - elf_segs_hash_verify_entry, Start
B - 129950 - PBL, End
B - 138378 - SBL1, Start
B - 196206 - pm_device_init, Start
B - 216336 - PM_SET_VAL:Skip
D - 18422 - pm_device_init, Delta
B - 217648 - boot_config_data_table_init, Start
D - 30 - boot_config_data_table_init, Delta - (0 Bytes)
B - 226401 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B - 233294 - sbl1_ddr_set_params, Start
B - 237107 - Pre_DDR_clock_init, Start
D - 244 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 249825 - pm_driver_init, Start
D - 4483 - pm_driver_init, Delta
B - 256078 - cpr_init, Start
D - 122 - cpr_init, Delta
B - 260744 - cpr_cx_mx_apc_vol_update, Start
D - 91 - cpr_cx_mx_apc_vol_update, Delta
B - 275933 - clock_init, Start
D - 152 - clock_init, Delta
B - 276177 - boot_flash_init, Start
D - 39223 - boot_flash_init, Delta
B - 318420 - boot_flash_swi_ddr_init, Start
D - 29402 - boot_flash_swi_ddr_init, Delta
B - 485072 - hw_family:5, hw_type:28, hw_rev:40
B - 489037 - SSMEM init OK
B - 506117 - USB non-zero endpoint requirements: 9 in, 5 out
B - 507764 - opening partition 0:SWIFOTA
B - 509960 - error for readpage:0
B - 2514969 - SVC PIN detected
B - 2515548 - DWL-get: ecnt=0 code=7
B - 2529090 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE
B - 2535434 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B - 2535953 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B - 2547207 - flags: u=1 e=1 obmsk=c,0
B - 2558096 - ssmem_release: region 20 not exists
B - 2558157 - ssmem_get: region 20 not exists
B - 2564897 - smart recovery counter cleared
B - 2564958 - DWL-ety: rea=1 rcv=0
B - 2784131 - Sahara over USB

Can someone please give me the directions in fixing the issue.

  1. plug in to Windows, it should have a DM port on device manager.
  2. use 7zip to extract the FW upgrade one click exe.
  3. use command prompt to run fdt2.txt xxx.spk